PYLE Audio PP-5200 Uživatelský manuál Strana 1

Rev.: A0 Aura Series (PP-5000 / PP-5200) Thermal Printer User's Guide IMPORTANT!!!! Please read carefully before using

2 - 2 2. When to replace paper Whenever the printer gives paper out signal or a red line appears on the thermal paper, it is the proper timing for

2 - 3 keep parallel interface in fast operation, please adjust in setup window the switch positions both 1, and 2 to ON leaving the rest unchanged

2 - 4 5. Power on When all the above cable connections are made correctly, you may connect your power adaptor to the wall outlet. Make sure that th

2 - 5 The header is printed in text mode and the rest part of this slip is printed in page mode. If FEED button is pressed at this moment, a font ta

2 - 6 either paper near end sense or paper feed action. It is also noticed that some market available paper roll has extremely light bobbin, easily

3 - 1 III. MAINTENANCE GUIDES A. MAINTENANCE GUIDE LINES • Always turn off and disconnect power before opening the hood or cover. • The areas aro

3 - 2 Before putting back the paper roll for printing, alcohol solvent must be dried completely. D. TROUBLE SHOOTING This section gives solutions to

3 - 3 If there is no paper jam and the print head is not overheated, turn off the printer and wait for half a minute then turn it back on. If the pr

3 - 4 setup and changing the switch positions 1 and 2 in the printer setup window to ON may help. 3. Paper Jam Problems Paper is jammed inside the

3 - 5 cutter blade along the track and reset it to home position. Please test push the top hood release button from time to time to see if the hood

P/N: 19740900010 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with t

3 - 6 Please use manual cutter as temporary alternative measure once the auto cutter malfunctioned. 5. Advanced Analysis Tool This printer supports

4 - 1 IV. SPECIFICATIONS A. PRINTER ITEM SPECIFICATION Printing method Thermal sensitive line dot method Effective printing width 54 mm Thermal

4 - 2 C. POWER ADAPTOR ITEM REQUIREMENT INPUT VOLTAGE 100 V AC ~ 250 V AC INPUT FREQUENCY 50 ~ 60 HZ INPUT CURRENT 1.5 A MAX. @ 115 V AC OUTPUT

5 - 1 V. TECHNICAL INFORMATION A. INTERFACES 1. Peripheral interface The connector for peripheral control is a 6P6C RJ11 jack with the following p

5 - 2 2. Serial interface The serial interface cable is a RJ45 plug to DB9F cable of length 1.8 meters (about 6 feet). To use the serial interface

5 - 3 points to the connector area of the printer. The OFF direction points to the power switch. The functions of each position may evolve with the

5 - 4 For switch position 5, if the switch is set to ON, the busy signal is sent to host only when input buffer is full. When it is set to OFF, busy

6 - 1 VI. USEFUL TIPS • Please note that only those qualified technicians may adjust several jumpers for some technical settings. Please visit ou

6 - 2 • Do not use a power outlet of a circuit shared with any equipment that uses a lot of power or causes great electrical noises, such as a copi

i Table Of Contents GETTING STARTED . . . . . . . . . . . . . . . . . . . . . 1 -- 1 CONGRATULATION . . . . . . . . . . . . . . . . . . . . . . 1

ii Printing problems . . . . . . . . . . . . . . . . . . . . .3 -- 2 Paper jam problems . . . . . . . . . . . . . . . . . . . 3 -- 4 Auto cutter

1 - 1 I. GETTING STARTED A. CONGRATULATION You have made a very wise decision by purchasing the easy loading ; low noise ; high resolution ; light

1 - 2 Aura series also supports user’s company’s LOGO downloading for superior performance. It even supports some enhancement capability for remind

1 - 3 ordered). b Power supply cable (when no power adaptor ordered) This printer power supply cable is used to supply power to the printer from the

1 - 4 F. INDICATORS • Power LED: green • Error LED: red • Paper Out LED: red Parallel Connector Serial

2 - 1 II. QUICK START-UP A. LOADING PAPER 1. Desk top application 1. Press down the hood release button to release the top hood. 2. Raise